HomeBusiness6 COMMON GARAGE DOOR REPAIR FOR HOMES

6 COMMON GARAGE DOOR REPAIR FOR HOMES

If your garage door is broken, it’s important to get the job done right. A poor garage door repair can lead to problems with other parts of your home that may not be visible. This means that you need a professional who knows how to fix these types of issues in order to keep everything running smoothly in your home.

Garage Door Repair

It is important to get the right parts. You need to make sure that your garage door repair company uses the right parts and tools, so they can do a good job with minimal problems.

You should also do it right the first time if possible; this will prevent any further issues down the road and save you money in the long run. If you don’t know how to fix something properly, then it will cost more money for someone else who does know what they’re doing!

Finally, find a good garage door repair company who has experience with your type of door (or even better yet – a company that specializes in garages). This way there’s less chance that things won’t go wrong when someone comes out here trying their hand at fixing things up like me!

Broken cables, springs, hinges and rollers

  • Cables
  • Springs
  • Hinges and rollers
  • Dents in the panels can be repaired by filing down the dent or replacing it with a section of new panel material. If you have a dent that is too deep for this, then you will need to replace all of your panels at once. The cost of this repair varies depending on how many panels are affected and what type of material they are made from (wood, fiberglass or steel).

Sagging doors

Sagging doors are the most common garage door problem. A sagging track is a bent track that causes your garage door to droop down, preventing it from opening fully and closing properly. This can be caused by many different things, including:

  • A broken spring or cable
  • Bent tracks (see below)
  • An improperly aligned hinge pin or spring tensioner

Bent tracks

Bent tracks are caused by a number of factors. These can include:

  • Defective garage door opener, which causes the tracks to warp or break
  • Warped rollers or rollers that aren’t properly lubricated (this is especially common with new garage doors)

If you have bent tracks, it’s time to fix them before they cause any other problems! To do this yourself, follow these steps:

  • Purchase new replacement parts from your local hardware store or online retailer if possible; otherwise, contact an experienced technician for assistance in fixing your bent track problem

Dented panels

Denting a garage door panel is one of the most common garage door repair jobs. If you have dented panels, it is important to fix them before they become worse and more expensive to repair.

Here’s how you can repair a dented panel yourself:

  • Use a metal coat hanger or long piece of wire to remove any dirt or debris that may be stuck in between the slats.
  • Use an electric drill with an appropriate bit (usually ¼ inch) on your drill press or power drill and gently guide it along the edge of each slat until all four sides are free from holes up through its centerline. Make sure not too much pressure is applied otherwise you may warp or break off some plastic pieces inside which would cause further issues later on down road when trying to open/close doors again after fixing them up again!

Unresponsive remotes and keypads

If you’re having trouble with your garage door remote or keypad, it is probably because the batteries are dead. In this case , take some time to check them out first.

In case your battery is fine and there are no visible signs of corrosion or leakage on your remote or keypad, then it’s possible that something else is wrong with it. First things first: make sure you’ve pressed all four buttons on both sides of any given device (if there are multiple remotes). If they don’t respond when pressed but do respond when touched by hand lightly—a common issue caused by sweaty fingers—it could mean that dirt got stuck in between two parts of a mechanism. Try removing any debris with a toothpick before trying again in order to avoid damaging anything further down its path toward failure!

Noisy garage doors

Noisy garage doors are a common problem for homeowners. They can be caused by many things, including:

  • Misaligned panels and track. This happens when the door doesn’t fit properly in its frame, causing it to rub against the walls of your garage.
  • Worn-out springs or rollers that are no longer strong enough to hold up a heavy garage door panel and keep it from rubbing against its frame during operation.
  • Warped panels that are being forced together by rusting screws or bolts holding them together at their edges (this also makes them more likely to break).

There are a variety of garage door parts that can break or wear out.

You may have a broken garage door or one that’s just not working right. You can check if it’s an issue with the cables, springs, hinges and rollers by looking at them closely. If you see any of these problems:

  • Sagging doors
  • Bent tracks (they’ll just not open all the way)
  • Dented panels (they’ll be bent inwards)
  • Unresponsive remotes and keypads (the buttons don’t work anymore)

You know your door needs fixing!

Conclusion

We hope that this article has helped you understand how to troubleshoot your own garage door problems. If you have any questions or need further assistance, please don’t hesitate to contact us today. We will be happy to help!

Must Read

spot_img